<p>O objetivo deste estudo foi avaliar a influência dos sistemas adesivos simplificados (condicionamento ácido total e auto-condicionante) e fluorfosfato acidulado a 1,23% (FFA) na resistência de união ao microcisalhamento (μ-RUC) de resinas compostas em molares e incisivos decíduos. O esmalte vestibular de quarenta molares e quarenta incisivos decíduos foi tratado com Clearfil SE Bond (CSE, Kuraray) ou Adper Single Bond 2 (SB2, 3M/ESPE). Cada grupo foi subdividido com base no tratamento prévio do esmalte com ou sem aplicação tópica de FFA a 1,23%. Em seguida, matrizes foram posicionadas e preenchidas com resina composta e posterior fotopolimerização. Depois da armazenagem em água destilada a 37±1 °C por 24 h, os espécimes foram submetidos ao μ-RUC em uma máquina de ensaio universal. Teste Kruskal-Wallis e Mann-Whitney (p<0,05) mostraram que a aplicação prévia de FFA a 1,23% levou a uma redução significativa na resistência de união. O tipo de adesivo não exerceu influência significativa na resistência de união. Na análise intergrupos, entretanto, redução significativa na resistência de união foi encontrada para os incisivos quando CSE foi empregado sem FFA. Falha adesiva foi o tipo de fratura mais comum. A resistência de união foi afetada pela aplicação de FFA a 1,23% e tipo de dente.</p>

<p>The aim of this study was evaluate in vitro the influence of simplified adhesive systems (etch-and-rinse and self-etching) and 1.23% acidulated phosphate fluoride (APF) on the microshear bond strength (μ-SBS) of composite resins on primary molars and incisors. Forty primary molars and forty incisors vestibular enamel was treated with either the self-etching Clearfil SE Bond (CSE, Kuraray) or etch-and-rinse Adper Single Bond 2 (SB2, 3M/ESPE) adhesive system. Each group was subdivided based on the prior treatment of the enamel with or without the topical application of 1.23% APF. Thereafter, matrices were positioned and filled with composite resin and light cured. After storage in distilled water at 37±1°C for 24 h, the specimens were submitted to μ-SBS in a universal testing machine. Kruskal-Wallis and Mann-Whitney tests (p<0.05) showed that the prior application of 1.23% APF led to a significant reduction in bond strength. The type of adhesive exerted no significant influence bond strength. In the inter-group analysis, however, significantly bond strength reduction was found for the incisors when CSE was employed with APF. Adhesive failure was the most common type of fracture. The bond strength was affected by the prior application of 1.23% APF and type of tooth.</p>

The aim of the present study was to evaluate the tensile strength, elongation, microhardness, microstructure and fracture pattern of various metal ceramic alloys cast under different casting conditions. Two Ni-Cr alloys, Co-Cr and Pd-Ag were used. The casting conditions were as follows: electromagnetic induction under argon atmosphere, vacuum, using blowtorch without atmosphere control. For each condition, 16 specimens, each measuring 25 mm long and 2.5 mm in diameter, were obtained. Ultimate tensile strength (UTS) and elongation (EL) tests were performed using a Kratos machine. Vickers Microhardness (VM), fracture mode and microstructure were analyzed by SEM. UTS, EL and VM data were statistically analyzed using ANOVA. For UTS, alloy composition had a direct influence on casting condition of alloys (Wiron 99 and Remanium CD), with higher values shown when cast with Flame/Air (p < 0.05). The factors 'alloy" and 'casting condition" influenced the EL and VM results, generally presenting opposite results, i.e., alloy with high elongation value had lower hardness (Wiron 99), and casting condition with the lowest EL values had the highest VM values (blowtorch). Both factors had significant influence on the properties evaluated, and prosthetic laboratories should select the appropriate casting method for each alloy composition to obtain the desired property.

OBJECTIVE: To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. MATERIAL AND METHODS: A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled) and three brands of silver nitrate salt (Merck, Synth or Cennabras) at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h) and concentrations (1, 5, 25, 50%) of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukey's test were used for data analyses (α=5%). RESULTS: The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9). Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm). In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000). CONCLUSIONS: Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were capable of indicating loss of marginal seal in the composite restorations; the 3-step conventional adhesive system had better performance regarding microleakage in enamel on primary and permanent teeth.

O presente estudo analisou a resistência à flexão de três compósitos recomendados para restaurações estéticas diretas: um compósito poliácido-modificado (Dyract AP), uma resina composta unimodal (Filtek Z250) e uma resina composta híbrida (Point 4). Os fatores de variação, além do tipo de compósito, foram o método de fotoativação e o período de armazenagem em água. Os materiais foram fotoativados continuamente por 40 s (500 mW/cm²) ou com intensidade de luz crescente (0-800 mW/cm² por 10 s seguidos de 30 s a 800 mW/cm²). Os períodos de armazenagem foram de 24 horas ou 30 dias em água destilada a 37°C. Os dados foram submetidos à análise de variância e ao teste de Tukey para comparações múltiplas (alfa = 0,05). A resina composta Z250 apresentou a maior média de resistência à flexão (166,74 MPa) e a Dyract AP, a menor (129,76 MPa). A armazenagem por 30 dias diminuiu a resistência à flexão para o método de fotoativação crescente (24 h: 156,64 MPa; 30 dias: 135,58 MPa). O método de fotoativação isoladamente não conduziu a diferentes valores de resistência à flexão.

The present study evaluated the flexural strength of three composite resins recommended for direct esthetic restorations: a polyacid modified composite (Dyract AP), a unimodal composite resin (Filtek Z250) and a hybrid composite resin (Point 4). The variation factors, apart from the type of composite resin, were the light activation method and the water storage period. The composite resins were light-cured in continuous mode (40 s, 500 mW/cm²) or in ramp mode (0-800 mW/cm² for 10 s followed by 30 s at 800 mW/cm²) and stored for 24 hours or 30 days in distilled water at 37°C. The data were analyzed by ANOVA and Tukey test for multiple comparisons (alpha = 0.05). The composite resin Z250 presented the highest mean flexural strength (166.74 MPa) and Dyract AP presented the lowest one (129.76 MPa). The storage for 30 days decreased the flexural strength in ramp mode (24 h: 156.64 MPa; 30 days: 135.58 MPa). The light activation method alone did not lead to different flexural strength values.

Este estudo avaliou a microdureza de ligas de Ni-Cr usadas em prótese fixa fundidas sob diferentes condições. As condições de fundição foram: (1-maçarico) chama composta por uma mistura de gás/oxigênio e centrífuga sem o controle do ambiente de fundição; (2-indução/argônio) indução eletromagnética com o ambiente controlado com argônio; (3-indução/vácuo) indução eletromagnética com o ambiente sob vácuo; (4-indução/ar) indução eletromagnética sem o controle da atmosfera. Foram utilizadas três ligas: Ni-Cr-Mo-Ti, Ni-Cr-Mo-Be e Ni-Cr-Mo-Nb. Foram realizadas 4 fundições com 5 espécimes cilíndricos de 15 mm de comprimento (diâmetro de 1,6 mm). Depois das fundições os espécimes foram embutidos e polidos para as mensurações de microdureza Vickers (VH) em um Shimadzu HMV-2 (1.000 g por 10 s). Um total de 5 indentações foram feitas por anel, uma em cada espécime. Os dados de VH foram avaliados pelos testes de ANOVA e Tukey (alfa = 0,05) para contraste de média. A microdureza das ligas apresentou a seguinte ordem: Ni-Cr-Mo-Ti (422 ± 7,8) > Ni-Cr-Mo-Nb (415 ± 7,6) > Ni-Cr-Mo-Be (359 ± 10,7), sendo diferentes entre si. Os valores obtidos nas condições indução/argônio e indução/vácuo foram semelhantes entre si (p > 0,05) e menores que os obtidos nas condições indução/ar e maçarico, estes últimos semelhantes entre si (p > 0,05). A microdureza das ligas é dependente da composição da liga e do método de fundição. A dureza das ligas de Ni-Cr foi maior quando fundidas nas condições indução/ar e maçarico.

This study evaluated the microhardness of Ni-Cr alloys used in fixed prosthodontics after casting under different conditions. The casting conditions were: (1-flame/air torch) flame made of a gas/oxygen mixture and centrifugal casting machine in a non-controlled casting environment; (2-induction/argon) electromagnetic induction in an environment controlled with argon; (3-induction/vacuum) electromagnetic induction in a vacuum environment; (4-induction/air) electromagnetic induction in a non-controlled casting environment. The 3 alloys used were Ni-Cr-Mo-Ti, Ni-Cr-Mo-Be, and Ni-Cr-Mo-Nb. Four castings with 5 cylindrical, 15 mm-long specimens (diameter: 1.6 mm) in each casting ring were prepared. After casting, the specimens were embedded in resin and polished for Vickers microhardness (VH) measurements in a Shimadzu HMV-2 (1,000 g for 10 s). A total of 5 indentations were done for each ring, one in each specimen. The data was subjected to two-way ANOVA and Tukey's multiple comparison tests (alpha = 0.05). The VH values of Ni-Cr-Mo-Ti (422 ± 7.8) were statistically higher (p < 0.05) than those of Ni-Cr-Mo-Nb (415 ± 7.6). The lowest VH values were found for Ni-Cr-Mo-Be (359 ± 10.7). The VH values obtained in the conditions induction/argon and induction/vacuum were similar (p > 0.05) and lower than the values obtained in the conditions induction/air and flame/air torch (p < 0.05). The VH values in the conditions induction/air and flame/air were similar (p > 0.05). The microhardness of the alloys is influenced by their composition and casting method. The hardness of the Ni-Cr alloys was higher when they were cast with the induction/air and flame/air torch methods.

Este estudo avaliou os efeitos de métodos para envelhecimento na microinfiltração de um sistema adesivo usado para selar superfícies oclusais. Após o condicionamento com ácido, as superfícies de 60 dentes permanentes foram contaminadas com 1 mL de plasma e seladas com OptiBond dual cure, ativado pelo Optilux 501, no modo rampa. A amostra foi dividida em oito grupos experimentais e um grupo controle ou imediato O envelhecimento dos espécimes foi realizado por 20 dias a 5, 37, 55 e 5-55°C (200 ciclos/dia) em contato com a água ou não. Após submeter os espécimes à técnica de infiltração com AgNO3, eles foram secionados duas vezes e os valores médios da penetração do corante foram tratados por análise de variância. Nenhum grupo apresentou vedamento hermético na interface, nem mesmo o grupo sem envelhecimento (imediato ou controle). O grupo que permaneceu a 5°C sem contato com a água mostrou o menor grau de penetração (p=0,015) e a interação envelhecimento x água foi significante (p=0,033). Os resultados levam às seguintes conclusões: 1) todos os grupos mostram microinfiltração, inclusive o controle; 2) o grupo mantido a 5ºC sem contato com a água mostrou os menores valores de microinfiltração; 3) em contato com a água, as variações térmicas parecem não afetar o grau de penetração do corante.

This study evaluated the effects of aging methods on the microleakage of an adhesive system used for sealing pit and fissure surfaces. After acid etching, the occlusal surfaces of 60 permanent teeth were contaminated with 1mL of human plasma and then sealed with OptiBond dual cure, activated in the ramp mode (Optilux 501). The sample was then divided into eight experimental and a control groups. Aging was performed for 20 days in 5, 37, 55 and 5-55ºC (200 cycles/day) under water contact or not. After subjecting the specimens to the AgNO3 technique, they were sectioned twice. Dye penetration was measured and the mean values were subjected to ANOVA. No group provided hermetic seal against dye penetration, even the control group (without treatment). Significant aging x water interaction effect (p=0.033) was observed. The group without water contact at 5ºC (p=0.015) showed the least dye penetration value. The results led to the main conclusions: 1) all groups showed dye penetration, even the control group; 2) storage teeth at 5ºC on dry condition provided the lowest degree of dye penetration; 3) in the presence of water, the temperature variations seem not to affect the microleakage values.